-
14 gauge steel-ell bracket with 9 gauge strap with set screw. Designed to screw onto wood rail and be supported by steel fence post. Very popular item to run wood fencing using steel posts. Please see additional information below for further details
-
Heavy 3/16” x 2” steel bracket with 9 gauge hinge strap designed to be used with carriage bolt to tighten strap using 3/8” x 3 1/2" bolt (not included). Please see additional information below for further details
-
Heavy 3/16” x 2” bracket with 9 gauge strap with set screws. Differs from above due to thicker steel and no lip; so can be mounted anywhere on flat surface. Please see additional information below for further details
-
Male post hinges made in 8 gauge galvanized steel and have 5/8" pins. Heavy male hinge uses 3" x 5" plate for attachment. Please see additional information below for further details
-
Available in sizes that our deluxe unit is not available in. Hub is pressed steel with 4 – ½” x 2 ½” carriage bolts. Comes with 1 1/8” shaft and grease fitting. * Deluxe rollers have needle bearings. Please see additional information below for further details
-
90º hinge assembly designed to fit 1 5/8” or 1 7/8” gate frame. Please see additional information below for further details
-
Bracket designed for baseball backstops allowing angled top pipes for containment. Please see additional information below for further details
-
One piece corner arms designed for 3-wire barb standoffs made from malleable steel. Please see additional information below for further details
-
Available in many sizes and attaches with a bent bolt. Very popular clean looking installation. Please see additional information below for further details
-
One-piece base with open bottom with four-corner bolt flange. Also has set screws for pipe security. Please see additional information below for further details
-
Malleable gate rest. Please see additional information below for further details
-
Also commonly known as a duckbill, this unit bolts to pipe to keep gate open. Please see additional information below for further details
-
Heavy 3/16” x 2” steel bracket with 9 gauge strap with set screw. Similar to inside corner wood fence adapter but to be used for outside installation. Does not have lip, so it can be mounted on any flat surface. Please see additional information below for further details
-
Panel clamps are a two-piece clamp designed to secure prefabricated panels on freestanding enclosures. These clamps are made from 8 gauge x 1 1/2" wide steel with approximately 1/2" spacing between the two pieces of tubing. Carriage bolt and nut sold separately. Please see additional information for further details
-
12 gauge x 3/4" 2 piece strap steel clamp designed to join two pipes at 90º angles. Used mainly in the construction of greenhouses, but can also be used to build portable buildings and for many other uses. Strap steel which is twisted and galvanized, are sold without bolts. Please see additional information below for further details
-
Steel bracket to attach a round post to the side of a wall. Please see additional information below for further details
-
Post hinges are a fitting that attaches to the gatepost, the pintle of which fits the frame hinge permitting the gate to swing. These hinges are made from 8 gauge x 1 1/4" wide or 8 gauge x 1 1/2" wide steel. A 3/8" x 2" through 3 1/2" carriage bolt and nut are used. Carriage bolt and nut sold separately. Please see additional information below for further details
-
Pressed steel barbed wire corner arms are a post fitting used to hold barbed wire in place. These arms are angled at 45º and hold three strands of barbed wire. Please see additional information for further details
-
A gate fitting used to hold a gate in place when closed. Used on 1 3/8” gate frame with two fork sizes of 1 7/8" & 2 3/8". Has padlock hole under latch to secure gate. Please see additional information below for further details
-
Gate collars are attached to a gate fork and post with carriage bolts to form a gate latch assembly. The collars are made of 8 gauge steel and come in three sizes to fit various post sizes such as: 1 3/8" 1 5/8" 1 7/8" Please see additional information below for further details
-
6" x 6" x 1/4" steel flanges with 5/8" holes at each corner. Has 5 1/4" tall flange with 2 set screws to secure tubing. Available for 2", 2 1/2", 3" tubing. The 4” tubing is on a 8x8x1/4” plate. Our galvanized flanges are 1/4" thick. Used for many job start scenarios involving anchoring steel tubing to flat surfaces. Please see additional information below for further details
-
Steel plates designed for attaching tubing to flat surfaces. Available in many other sizes, call for availability. Please see additional information below for further details
-
Steel trough with 12” flat spike for ground anchoring. Designed to accept gate drop rods. Please see additional information below for further details
-
Gate clips are 12 gauge steel fittings used to attach gate fabric to the vertical sides of a gate frame. Please see additional information below for further details
-
This unit bolts to a pipe to keep gate open. Please see additional information below for further details
-
Gate scrolls are decorative fittings attached to gates along the top gate railing. Please see additional information below for further details
-
Pressed steel 180º gate hinges are a swing gate hinge that permits the gate to swing 180º from the closed to the open position. Please see additional information for further details
-
Pressed steel barbed wire V-type corner arms are a post fitting used to hold barbed wire in place. These arms are "V" shaped and hold 6 strands of barbed wire. Please see additional information for further details
-
Offset rail ends are a cup-shaped fitting used with a brace band, carriage bolt and nut to connect the top rail or brace to a post. Carriage bolt and nut sold separately. These have 1 hole and the tab is fastened to top of cup at a 45º. Combination rail ends are a cup-shaped fitting used with a brace band, carriage bolt and nut to connect the top rail to a post in conjunction with connecting the truss rod. Carriage bolt & nut is sold separately. These have 2 holes for 3/8" truss rods and 45º tab having 1 hole. Brace rail ends are a cup-shaped fitting used with a brace band, carriage bolt and nut to connect the top rail or brace to a post in conjunction with connecting the truss rod. Carriage bolts and nuts sold separately. Tab has 2 holes and is welded to cup parallel to the ground, there are no holes in the cup. Please see additional information below for further details
-
Post hinges are a fitting that attaches to the gatepost, the pintle of which fits the frame hinge permitting the gate to swing (also called male hinge). These hinges are made from 8 gauge x 1" wide steel. A 3/8" x 1 1/2" through 3 1/2" carriage bolt is used. Carriage bolt and nut are sold separately. Please see additional information below for further details
-
Regular pressed steel forks are 8 gauge x 3/4" fittings that along with gate collars form a fork latch assembly. These forks come in three sizes: 1 3/8" 1 7/8" 2 3/8" Please see additional information below for further details
-
A fitting normally used in residential jobs to hold the gate in place when closed. Sizes available are for a 1 3/8" gate post for collar attachment and three sizes for the regular forks to close to: 1 3/8" 1 7/8" 2 3/8" Please see additional information below for further details
