-
Line wood adaptor for 2 3/8" steel posts. Bracket is 13ga. X 2" X 6", and strap is 13ga. X 7/8". Designed to use 2 - 5/16" X 1 3/4" carriage bolts (not included). Bracket has 4 holes for rail attachment. Please see additional information below for further details
-
Galvanized steel brackets designed to join 2 wood rails together. Made from 18 gauge steel. Please see additional information below for further details
-
Rollers designed for wood gates. Available for lag screwing to gate rails, in either fixed or swivel configurations. Uses 6” solid rubber tires. Swivel gate roller uses 4" x 4" x 1/8" plate with 4 holes for sturdy mounting.
-
Welded Wire Panel Clamps are designed to join 2 welded wire panels together where you do not have a post. Material is 11 gauge x 1. Please see additional information for further details
-
Welded Wire Clamps are designed to attach welded wire panels to the post for support of your panels. Available in 1 5/8”, 1 7/8”, 2 3/8”, 2 7/8” and 4” sizes. Material is 11 gauge x 1. Please see additional information for further details
-
Welded Wire Clamps are designed to attach welded wire panels to the post for support of your panels. Available in 1 5/8”, 1 7/8”, 2 3/8”, 2 7/8” and 4” sizes. Material is 11 gauge x 1. Please see additional information for further details
-
Weld-On Post Hinge - Galvanized steel bracket designed to be welded or bolted on any flat surface. This is the male hinge in 5/8” size. Square Post Hinge - Galvanized male hinges designed to bolt on square tubing. These have 5/8” pins, using 3/8” bolts for attachment; not included. Please see additional information below for further details
-
Weld on male 9 gauge steel hinge with 5/8" pin makes a very strong hinge. Please see additional information below for further details
-
Weld on female 8 gauge steel hinge with 5/8" pinhole, makes a very strong hinge. Please see additional information below for further details
-
Designed for corral panels, uses 9" corral pin for attachment. Weld on style. 9 gauge. Please see additional information below for further details
-
Weld on caps are fittings welded atop a post usually to exclude water from tubular posts. Please see additional information below for further details
-
12 gauge flat bracket designed for 1 3/8“ fork assemblies. Can be attached to any flat surface with 1/2" lags. Please see additional information below for further details
-
Walk gate sets are a package of all necessary parts to install a single walk gate. The components consist of: 2 - female gate hinges 1 - fork latch assembly 2 - male post hinges 4 - carriage bolts and nuts The J-bolt walk gate set comes with 2 - 5/8" x 4 1/2" J-bolts instead of 2 - male post hinges. All the components are packaged in a clear poly bag. These kits are for 1 3/8" gate frames and either 1 7/8" or 2 3/8" male post hinges for gate posts or J-bolts. Please see additional information below for further details
-
Walk gate sets are a package of all necessary parts to install a single walk gate. The components consist of: 2 - female gate hinges 1 - fork latch assembly 2 - male post hinges 4 - carriage bolts and nuts The J-bolt walk gate set comes with 2 - 5/8" x 4 1/2" J-bolts instead of 2 - male post hinges. All the components are packaged in a clear poly bag. These kits are for 1 3/8" gate frames and either 1 7/8" or 2 3/8" male post hinges for gate posts or J-bolts. Please see additional information below for further details
-
6" x 2" wide wheel designed for double front trucks using embedded angle channel for tracking of gates. Can be purchased installed on double front trucks. Call for availability. Please see additional information below for further details
-
Latch assembly kit comes with everything needed to install latch on wood fence. ** Latches include (1) LATCH, (1) HANDLE, (1) STRIKER PIN, and POWDER COATED LAG SCREWS per plastic bag - 12 bags per box. Please see additional information below for further details
-
14 gauge flat bracket with holes at all four corners, designed to fit any post from 1 3/8" to 4 1/2" by using proper brace band for attachment. Design features smooth backside of post. Band, bolt and nut sold separately. Please see additional information below for further details
-
Dual Top Plate is used to cover the top of the post. Universal Post Plate bracket is used to attach two post together, which allows horizontal rail to run through the center of your posts. Please see additional information below for further details
-
Universal pressed steel box hinges are a swing gate hinge that permits the gate to swing 90º from the closed to the open position. Universal box hinges are attached to the post with a strap and four 3/8" carriage bolts. These hinges are universal because they fit post sizes 2 1/2" through 4 1/2". Bolts and nuts included. Please see additional information below for further details
-
Please see additional information below for further details
-
Two-way brace bands are a symmetrically formed strip of metal shaped to fit around a post and used with a carriage bolt and nut to attach the two rail ends or two brace rail end and truss rod tighteners to the post. Also used for attaching barbed wire, tension wire, and other items to a terminal post. These bands are made from 12 gauge x 3/4" steel. This gauge band is used in residential and other light duty applications. A 5/16" x 1 1/4" carriage bolt is used. Carriage bolt and nut sold separately. Sometimes called 180º bands. Please see additional information below for further details
-
Two-way brace bands are a symmetrically formed strip of metal shaped to fit around a post and used with a carriage bolt and nut to attach the two rail ends or two brace rail end and truss rod tighteners to the post. Also used for attaching barbed wire, tension wire, and other items to a terminal post. These bands are made from 11 gauge x 1". This gauge band is used in heavy-duty commercial applications. A 3/8" x 1 1/2" carriage bolt is used. Carriage bolt and nut sold separately. Sometimes called 180º bands. Please see additional information below for further details
-
Truss rod tigteners are used to provide support to gate corner posts by way of truss rods that are attached to the tighteners and posts. Please see additional information below for further details
-
Top rail sleeves are fittings used to join two pieces of top rail when a swedged top rail is not used. Please see additional information below for further details
-
These arms are 16” in length welded to a 3” x 3” x ¼” plate and are designed to hold 3 strands of barb wire in place. They are designed to be installed to the top of a post or top of a wall and are domestically produced. Please see additional information for further details
-
Galvanized steel bars designed to pull fabric tight and to attach to tension bands. Available for 4’, 5’, and 6 ft. heights. Please see additional information below for further details
-
Tension bands are an offset strip of metal shaped to fit around the terminal post and used with a carriage bolt and nut to attach the tension bar to the post. These bands are made from 14 gauge x 3/4" steel. This gauge band is used in residential and other light duty applications. A 5/16" x 1 1/4" carriage bolt is used. Carriage bolt and nut sold separately. Please see additional information below for further details
-
Tension bands are an offset strip of metal shaped to fit around the terminal post and used with a carriage bolt and nut to attach the tension bar to the post. These bands are made from 13 gauge x 7/8" steel. This gauge band is used in medium duty applications. A 5/16" x 1 1/4" carriage bolt is used. Carriage bolt and nut sold separately. Please see additional information below for further details
-
Tension bands are an offset strip of metal shaped to fit around the terminal post and used with a carriage bolt and nut to attach the tension bar to the post. These bands are made from 11 gauge x 1" steel. This gauge band is used in heavy-duty commercial applications. A 3/8" x 1 1/2" carriage bolt is used. Carriage bolt and nut sold separately. Please see additional information below for further details
-
Designed to add height and 3-wire capability to any size T-post 1.01 - 1.50 weight. Can be manufactured to fit on either side of T-post. Please see additional information for further details
-
14 gauge pressed steel bracket designed to hold rails when building fence using T-post. Has lip on bottom and set screw digs into “T” on post for secure fastening. Please see additional information below for further details
-
Drivers designed to install T-posts. Weight is approximately 22 lbs. A must to install posts. Please see additional information below for further details
-
Rollers designed to attach to frame of gate either inline or offset. Will work on 1 3/8”, 1 5/8”, or 1 7/8” tubing. Available with 6” or 8” rubber wheels. Swivel assemblies will work better on irregular surfaces. Please see additional information below for further details
-
These bars are designed to pull chain link fabric using a puller or come a-long. They are available in 30”, 42”, and 68” sizes. Made from heavy gauge galvanized steel. Please see additional information below for further details
-
Plastic packed black strap hinges with lag screws. Available in 8” or 10” sizes. Screws are powder coated. ** Hinges come (1) PAIR with POWDER COATED LAG SCREWS per plastic bag - 10 bags per box. Please see additional information below for further details
-
Square Welded Wire Clamps are designed to attach welded wire panels to a square post for support of your panels. Material is 11 gauge x 1. Please see additional information for further details
-
Tension bands are an offset strip of metal shaped to fit around the terminal post and used with a carriage bolt and nut to attach the tension bar to the post. These bands are made from 13 gauge x 7/8" steel. Square bands are used in applications where square posts are used such as ornamental fence. A 5/16" x 1 1/4" carriage bolt is used. Carriage bolt and nut sold separately. Please see additional information below for further details
-
Galvanized bands designed for square tubing. Designed to pull fabric and attach to square tubing. 13 gauge x 7/8” for strength. Please see additional information below for further details
-
Square PS caps (also called square post caps) fit atop a square post usually to prevent water from corroding inner post and for decorative purposes. Please see additional information below for further details
-
Galvanized steel square forks to be used in conjunction with square collars above. Please see additional information below for further details
-
Square gate forks are used to attach to square tubing such as ornamental fencing. The square forks come in six sizes for post sizes ranging from 1" to 4". Please see additional information below for further details
-
Square gate collars are used with square tubing in ornamental fencing to attach to a gate fork and square post with carriage bolts to form a gate latch assembly. The collars are made with 8 gauge steel and come in four sizes: 1",1 1/4",1 1/2" ,2" Please see additional information below for further details
-
8 gauge x 1 1/4" wide galvanized collars for square tubing. Designed to hang square forks on square tubing. Please see additional information below for further details
-
Square post hinges are a fitting that attaches to the gate post, the pintle of which fits the frame hinge permitting the gate to swing. A 3/8" x 1 1/2" through 4 1/2" carriage bolt and nut is used. Carriage bolt and nut sold separately. 9 gauge. Please see additional information below for further details
-
11 gauge Square Line Rail Clamps are a two-piece clamp designed for 180° horizontal square rail connections to a square line post. Carriage bolt and nut sold separately. Please see additional information for further details
-
11 gauge Square Line Rail Clamps are a two-piece clamp designed for 180° horizontal square rail connections to a square line post. Carriage bolt and nut sold separately. Please see additional information for further details
